검색결과
-
[특집-기술위원회] TC 211 - 지리정보/지리학(Geographic information/Geomatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 211지리정보/지리학(Geographic information/Geomatics)과 관련된 기술위원회는 TC 210과 마찬가지로 1994년 결성됐다. 사무국은 스웨덴 국립표준청(Svenska institutet för standarder, SIS)에서 맡고 있다.위원회는 마츠 올린(Mr Mats Åhlin)가 책임지고 있다. 현재 의장은 피터 파슬로(Mr Peter Parslow)이며 임기는 2024년말까지다. ISO 기술 프로그램 관리자는 하킴 음킨시(Mr Hakim Mkinsi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등이다.범위는 디지털 지리정보 분야의 표준화다. 지구와 관련된 위치와 직간접적으로 연관된 물체나 현상에 관한 정보에 대한 구조화된 표준 세트 확립을 목표로 하고 있다.지리 정보의 범위 내에서 이러한 표준은 데이터 관리를 위한 방법, 도구 및 서비스를 지정할 수 있다. 데이터 관리는 사용자 및 시스템을 위한 데이터 획득, 처리, 분석, 접근, 제시 및 출판이 포함된다.이 작업은 가능한 경우 정보 기술 및 데이터에 대한 적절한 표준과 연결되어야 하며 지리 데이터를 사용하는 부문별 응용 프로그램 개발을 위한 프레임워크를 제공해야 된다.현재 ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준은 97개며 ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준은 26개다. 참여하고 있는 회원은 38개국, 참관 회원은 35개국이다.□ ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준 97개 중 15개 목록▷ISO 6709:2022 Standard representation of geographic point location by coordinates▷ISO 19101-1:2014 Geographic information — Reference model — Part 1: Fundamentals▷ISO 19101-2:2018 Geographic information — Reference model — Part 2: Imagery▷ISO 19103:2015 Geographic information — Conceptual schema language▷ISO 19104:2016 Geographic information — Terminology▷ISO 19105:2022 Geographic information — Conformance and testing▷ISO 19106:2004 Geographic information — Profiles▷ISO 19107:2019 Geographic information — Spatial schema▷ISO 19108:2002 Geographic information — Temporal schema▷ISO 19108:2002/Cor 1:2006 Geographic information — Temporal schema — Technical Corrigendum 1▷ISO 19109:2015 Geographic information — Rules for application schema▷ISO 19110:2016 Geographic information — Methodology for feature cataloguing▷ISO 19111:2019 Geographic information — Referencing by coordinates▷ISO 19111:2019/Amd 1:2021 Geographic information — Referencing by coordinates — Amendment 1▷ISO 19111:2019/Amd 2:2023 Geographic information — Referencing by coordinates — Amendment 2□ ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준 26개 중 15개 목록▷ISO/DIS 19103 Geographic information — Conceptual schema language▷ISO/CD 19109 Geographic information — General feature model and rules for application schema▷ISO/AWI TR 19115-4 Geographic information – Metadata — Part 4: JSON schema implementation of metadata fundamentals▷ISO/DIS 19116 Geographic information — Positioning services▷ISO/AWI TR 19121 Geographic information — Imagery and gridded data▷ISO/AWI 19123-2 Geographic information — Schema for coverage geometry and functions — Part 2: Coverage implementation schema▷ISO/AWI TS 19123-4 Geographic information — Schema for coverage geometry and functions — Part 4: Tiling Schema▷ISO/AWI TS 19124-2 Geographic information — Calibration and validation of remote sensing data and derived products — Part 2: SAR▷ISO/AWI 19127 Geographic information — Geodetic register▷ISO/AWI TS 19130-2 Geographic information — Imagery sensor models for geopositioning — Part 2: SAR, InSAR, lidar and sonar▷ISO/CD 19135 Geographic information registration — Requirements▷ISO/DTS 19144-3 Geographic information — Classification systems — Part 3: Land Use Meta Language (LUML)▷ISO/DIS 19152-2 Geographic information — Land Administration Domain Model (LADM) — Part 2: Land registration▷ISO/FDIS 19152-3 Geographic information — Land Administration Domain Model (LADM) — Part 3: Marine georegulation▷ISO/DIS 19152-4 Geographic information — Land Administration Domain Model (LADM) — Part 4: Valuation information
-
[특집-기술위원회] TC 199 - 기계류 안전(Safety of machinery)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 등이 있다.ISO/TC 199 기계류 안전(Safety of machinery)과 관련된 기술위원회는 1991년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 크리스티안 톰(Mr Dr. rer. nat Christian Thom)가 책임지고 있다. 현재 의장은 오토 괴르네만(Mr Otto Görnemann)이다.ISO 기술 프로그램 관리자는 메르세 페레 에르난데스(Mme Mercè Ferrés Hernández), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등이다.범위는 ISO/IEC 가이드 51 프레임워크 및 ISO, IEC 기술 위원회와 협력해 용어, 방법론, 보호 장치 및 안전 장치를 통합한 기계 안전에 대한 기본 개념 및 일반 원칙의 표준화다.단, ISO/IEC Guide 51에 정의되어 있고 다른 ISO 또는 IEC 기술 위원회의 작업에서 명시적으로 다루고 있는 제품 안전 표준은 제외한다.현재 ISO/TC 199 사무국의 직접적인 책임 하에 발행된 표준은 45개며 ISO/TC 199 사무국의 직접적인 책임 하에 개발 중인 표준은 9개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 199 사무국의 직접적인 책임 하에 발행된 표준 45개 중 15개 목록▷ISO Guide 78:2012 Safety of machinery — Rules for drafting and presentation of safety standards▷ISO 11161:2007 Safety of machinery — Integrated manufacturing systems — Basic requirements▷ISO 11161:2007/Amd 1:2010 Safety of machinery — Integrated manufacturing systems — Basic requirements — Amendment 1▷ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction▷ISO 13849-1:2023 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design▷ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation▷ISO 13850:2015 Safety of machinery — Emergency stop function — Principles for design▷ISO 13851:2019 Safety of machinery — Two-hand control devices — Principles for design and selection▷ISO 13854:2017 Safety of machinery — Minimum gaps to avoid crushing of parts of the human body▷ISO 13855:2010 Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body▷ISO 13856-1:2013 Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors▷ISO 13856-2:2013 Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars▷ISO 13856-3:2013 Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices▷ISO 13857:2019 Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs▷ISO 14118:2017 Safety of machinery — Prevention of unexpected start-up□ ISO/TC 199 사무국의 직접적인 책임 하에 개발 중인 표준 9개 목록▷ISO/AWI 12100 Safety of machinery — General principles for design — Risk assessment and risk reduction▷ISO/DIS 12895 Safety of machinery — Identification of whole body access and prevention of associated risk(s)▷ISO/AWI 13849-2 Safety of machinery — Safety-related parts of control systems — Part 2: Guidance for the design and validation▷ISO/AWI TR 13849-3 Safety of machinery — Safety-related parts of control systems — Part 3: Markov model-based PFH calculation▷ISO/FDIS 13855 Safety of machinery — Positioning of safeguards with respect to the approach of the human body▷ISO/FDIS 14119 Safety of machinery — Interlocking devices associated with guards — Principles for design and selection▷ISO/AWI 14122-1 Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means of access between two levels▷ISO/AWI 14159 Safety of machinery — Hygiene requirements for the design of machinery▷ISO/CD TR 21260 Safety of machinery — Mechanical safety data for physical contacts between moving machinery or moving parts of machinery and persons
-
[특집-기술위원회] TC 178 - 리프트·에스컬레이터·무빙워크(Lifts·escalators·moving walks)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 등이 있다.ISO/TC 178 리프트, 에스컬레이터, 무빙워크(Lifts, escalators and moving walks)와 관련된 기술위원회는 TC 176과 마찬가지로 1979년 결성됐다. 사무국은 프랑스 표준화기구(Association Française de Normalization, AFNOR)에서 맡고 있다.위원회는 에바 콘티발(Mme Eva Contival)가 책임지고 있으며 현재 의장은 게로 그슈벤트너(Dr Gero Gschwendtner)다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 리프트, 서비스 리프트, 승객용 컨베이어, 유사 장치 등의 안전을 포함해 모든 사양의 표준화다. 단 지속적인 기계적 취급 장비 및 광산 리프트는 제외한다.현재 ISO/TC 178 사무국의 직접적인 책임 하에 발행된 표준은 43개며 ISO/TC 178 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 31개국, 참관 회원은 27개국이다.□ ISO/TC 178 사무국의 직접적인 책임 하에 발행된 표준 43개 중 15개 목록▷ISO 4190-2:2001 Lift (US: Elevator) installation — Part 2: Class IV lifts▷ISO 4190-3:1982 Passenger lift installations — Part 3: Service lifts class V▷ISO 4190-5:2006 Lift (Elevator) installation — Part 5: Control devices, signals and additional fittings▷ISO 8100-1:2019 Lifts for the transport of persons and goods — Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts▷ISO 8100-2:2019 Lifts for the transport of persons and goods — Part 2: Design rules, calculations, examinations and tests of lift components▷ISO/TS 8100-3:2019 Lifts for the transport of persons and goods — Part 3: Requirements from other Standards (ASME A17.1/CSA B44 and JIS A 4307-1/JIS A 4307-2) not included in ISO 8100-1 or ISO 8100-2▷ISO 8100-20:2018 Lifts for the transport of persons and goods — Part 20: Global essential safety requirements (GESRs)▷ISO/TS 8100-21:2018 Lifts for the transport of persons and goods — Part 21: Global safety parameters (GSPs) meeting the global essential safety requirements (GESRs)▷ISO/TR 8100-24:2016 Safety requirements for lifts (elevators) — Part 24: Convergence of lift requirements▷ISO 8100-30:2019 Lifts for the transport of persons and goods — Part 30: Class I, II, III and VI lifts installation▷ISO 8100-32:2020 Lifts for the transportation of persons and goods — Part 32: Planning and selection of passenger lifts to be installed in office, hotel and residential buildings▷ISO 8100-33:2022 Lifts for the transport of persons and goods — Part 33: T-type guide rails for lift cars and counterweights▷ISO 8100-34:2021 Lifts for the transport of persons and goods — Part 34: Measurement of lift ride quality▷ISO 8102-1:2020 Electrical requirements for lifts, escalators and moving walks — Part 1: Electromagnetic compatibility with regard to emission▷ISO 8102-2:2021 Electrical requirements for lifts, escalators and moving walks — Part 2: Electromagnetic compatibility with regard to immunity□ ISO/TC 178 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 8100-1 Lifts for the transport of persons and goods — Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts▷ISO/DIS 8100-2 Lifts for the transport of persons and goods — Part 2: Design rules, calculations, examinations and tests of lift components▷ISO/AWI 8100-7 Lifts for the transport of persons and goods — Part 7: Accessibility to lifts for persons including persons with disability▷ISO/WD TS 8100-10 Lifts for the transport of persons and goods — Part 10: Building Information Modelling▷ISO/CD TS 8100-22 Lifts for the transport of persons and goods — Part 22: Prerequisites for certification of conformity of lift systems, lift components and lift functions within conformity assessment procedures▷ISO/CD TS 8100-23 Lifts for the transport of persons and goods — Part 23: Certification and accreditation requirements within conformity assessment procedures▷ISO/CD TR 8101-10 Fire safety on lifts — Part 10: Comparison of worldwide safety standards on lifts for firefighters▷ISO/AWI 8102-1 Electrical requirements for lifts, escalators and moving walks — Part 1: Electromagnetic compatibility with regard to emissions▷ISO/AWI 8102-2 Electrical requirements for lifts, escalators and moving walks — Part 2: Electromagnetic compatibility with regard to immunity▷ISO/WD TS 8102-21 Electrical requirements for lifts, escalators and moving walks — Part 21: Part 21: On-site and off-site software updates▷ISO/DIS 8103-1 Escalators and moving walks — Part 1: Safety requirements▷ISO/WD TS 8103-3 Escalators and moving walks — Part 3: Part 3: Requirements from other Standards (ASME A17.1/CSA B44 and JIS codes) not included in ISO▷ISO/AWI 8103-9 Escalators and moving walks — Part 9: Measurement of ride quality▷ISO/DTR 25741-1 Lifts and escalators subject to seismic conditions — Compilation report — Part 1: Rule by rule comparison▷ISO/DTR 25741-2 Lifts and escalators subject to seismic conditions — Compilation report — Part 2: Abbreviated comparison and comments
-
[특집-기술위원회] TC 174 - 보석 및 귀금속(Jewellery and precious metals)… 번호 부여 시스템, 반지 크기, 귀금속 색상 및 코팅, 다이아몬드 등 주얼리스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 등도 포함된다.ISO/TC 174 보석 및 귀금속(Jewellery and precious metals)과 관련된 기술위원회는 TC 171, TC 172, TC 173과 마찬가지로 1978년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 페트라 비쇼프((FH) Petra Bischoff)가 책임지고 있으며 현재 의장은 조나단 조드리(Mr Jonathan Jodry)이며 임기는 2024년까지다.ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 빈센조 바주치(M Vincenzo Bazzucchi) 등으로 조사됐다.범위는 번호 부여 시스템, 반지 크기, 귀금속 색상 및 코팅, 다이아몬드 등 주얼리 분야와 분석, 샘플링, 불순물 등 귀금속 분야 표준화다.현재 ISO/TC 174 사무국의 직접적인 책임 하에 발행된 표준은 21개며 ISO/TC 173 사무국의 직접적인 책임 하에 개발 중인 표준은 10개다. 참여하고 있는 회원은 19개국, 참관 회원은 25개국이다.□ ISO/TC 174 사무국의 직접적인 책임 하에 발행된 표준 21개 중 15개 목록▷ISO 5724:2023 Jewellery and precious metals — Determination of very high purity gold — Difference method using ICP-MS▷ISO 8653:2016 Jewellery — Ring-sizes — Definition, measurement and designation▷ISO 8654:2018 Jewellery — Colours of gold alloys — Definition, range of colours and designation▷ISO 8654:2018/Amd 1:2019 Jewellery — Colours of gold alloys — Definition, range of colours and designation — Amendment 1▷ISO 9202:2019 Jewellery and precious metals — Fineness of precious metal alloys▷ISO 10713:1992 Jewellery — Gold alloy coatings▷ISO 11210:2023 Jewellery and precious metals — Determination of platinum — Gravimetry using ammonium chloride▷ISO 11426:2021 Jewellery and precious metals — Determination of gold — Cupellation method (fire assay)▷ISO 11427:2014 Jewellery — Determination of silver in silver jewellery alloys — Volumetric (potentiometric) method using potassium bromide▷ISO 11490:2023 Jewellery and precious metals — Determination of palladium — Gravimetry using dimethylglyoxime▷ISO 11494:2019 Jewellery and precious metals — Determination of platinum in platinum alloys — ICP-OES method using an internal standard element▷ISO 11495:2019 Jewellery and precious metals — Determination of palladium in palladium alloys — ICP-OES method using an internal standard element▷ISO 11596:2021 Jewellery and precious metals — Sampling of precious metals and precious metal alloys▷ISO 13756:2015 Jewellery — Determination of silver in silver jewellery alloys — Volumetric (potentiometric) method using sodium chloride or potassium chloride▷ISO 15093:2020 Jewellery and precious metals — Determination of high purity gold, platinum and palladium — Difference method using ICP-OES□ ISO/TC 174 사무국의 직접적인 책임 하에 개발 중인 표준 10개 목록▷ISO/PRF 6893 Jewellery and precious metals — Inspection of batches of small diamonds — Terminology, classification and test methods▷ISO/DIS 10713 Jewellery and precious metals — Gold alloy coatings▷ISO/PRF 11427 Jewellery and precious metals — Determination of silver — Potentiometry using potassium bromide▷ISO/PRF 13756 Jewellery and precious metals — Determination of silver — Potentiometry using sodium chloride or potassium chloride▷ISO/DIS 18214 Jewellery and precious metals — Determination of high purity gold, silver, platinum and palladium — Difference method using SPARK-OES▷ISO/AWI 19376-1 Jewellery and precious metals — Vocabulary — Part 1: Precious metals and units▷ISO/CD 19919 Jewellery and precious metals — Determination of silver — ICP-OES method using an internal standard element▷ISO/AWI 21261-1 Jewellery and precious metals — Responsible precious metals — Part 1: General requirements for responsible precious metals▷ISO/AWI 21261-2 Jewellery and precious metals — Responsible precious metals — Part 2: Minimum rules and procedures for conformity assessment schemes▷ISO/AWI 21261-3 Jewellery and precious metals — Responsible precious metals — Part 3: Requirements for recycled gold
-
[기획-디지털 ID 법률] 7. 미국 유타주의 블록체인 디지털 ID 관련 법률 제정2023년 4월12일 미국 유타주지사(Utah governor) 스펜서 콕스(Spencer Cox)는 블록체인 디지털 ID 파일럿 법안에 서명했다.콕스 주지사가 서명한 법안은 디지털 기술 태스크 포스(Digital Technology Task Force) 법안 HB 357이다. 유타주 기술 서비스부(Division of Technology Services, DTS)가 디지털 검증 가능한 자격증명에 대한 파일럿 프로그램을 시작하도록 요구하는 법안이다.HB 470로 명명된 블록체인 디지털 ID 파일럿 법안에 따르면 기관은 분산원장 기술(distributed-ledger technology)을 통해 디지털 ID 또는 기타 기록을 발행하는 방법에 관해 정부기관에 권장 사항을 제공해야 된다.또한 DTS는 프로젝트가 시작된 후 2023년 10월 말까지 유타주 하원의 공공시설, 에너지, 기술 임시위원회에 디지털 기록의 진행 상황을 보고하도록 했다.유타주는 디지털 ID를 개발한 최초의 주와는 거리가 멀지만 블록체인 실험을 통해 다른 주와 차별화할 수 있을 것으로 판단하고 있다.참고로 콜로라도주는 2019년 앱 기반 디지털 운전면허증을 출시했다. 애리조나주는 2022년 애플 스마트폰 사용자가 디지털 ID를 저장해 사용하도록 기술을 개발했다.
-
[특집-기술위원회] TC 160 - 건물 유리(Glass in building)… 영국 표준협회(BSI)가 사무국 운영스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 등도 포함된다.ISO/TC 160 건물 유리(Glass in building)와 관련된 기술위원회는 TC 156, TC 157, TC 158, TC 159와 마찬가지로 1974년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는 톰 스택(Mr Tom Stack)이 책임지고 있으며 현재 의장은 노버트 브룩(Mr Dr Norbert Wruk)이다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등으로 조사됐다.범위는 용어, 성능 요구사항, 계산 및 테스트 방법, 설계 및 시공 규칙, 치수 특성을 포함한 재료의 분류 및 사양을 포함한 건물 유리 분야의 표준화다.현재 ISO/TC 160 사무국의 직접적인 책임 하에 발행된 표준은 58개며 ISO/TC 160 사무국의 직접적인 책임 하에 개발 중인 표준은 10개다. 참여하고 있는 회원은 22개국, 참관 회원은 30개국이다.□ ISO/TC 160 사무국의 직접적인 책임 하에 발행된 표준 58개 중 15개 목록▷ISO 1288-1:2016 Glass in building — Determination of the bending strength of glass — Part 1: Fundamentals of testing glass▷ISO 1288-2:2016 Glass in building — Determination of the bending strength of glass — Part 2: Coaxial double-ring test on flat specimens with large test surface areas▷ISO 1288-3:2016 Glass in building — Determination of the bending strength of glass — Part 3: Test with specimen supported at two points (four point bending)▷ISO 1288-4:2016 Glass in building — Determination of the bending strength of glass — Part 4: Testing of channel shaped glass▷ISO 1288-5:2016 Glass in building — Determination of the bending strength of glass — Part 5: Coaxial double ring test on flat specimens with small test surface areas▷ISO 9050:2003 Glass in building — Determination of light transmittance, solar direct transmittance, total solar energy transmittance, ultraviolet transmittance and related glazing factors▷ISO 10291:1994 Glass in building — Determination of steady-state U values (thermal transmittance) of multiple glazing — Guarded hot plate method▷ISO 10292:1994 Glass in building — Calculation of steady-state U values (thermal transmittance) of multiple glazing▷ISO 10293:1997 Glass in building — Determination of steady-state U values (thermal transmittance) of multiple glazing — Heat flow meter method▷ISO 11479-1:2011 Glass in building — Coated glass — Part 1: Physical defects▷ISO 11479-2:2011 Glass in building — Coated glass — Part 2: Colour of façade▷ISO 11485-1:2011 Glass in building — Curved glass — Part 1: Terminology and definitions▷ISO 11485-2:2011 Glass in building — Curved glass — Part 2: Quality requirements▷ISO 11485-3:2014 Glass in building — Curved glass — Part 3: Requirements for curved tempered and curved laminated safety glass▷ISO 12540:2017 Glass in building — Tempered soda lime silicate safety glass □ ISO/TC 160 사무국의 직접적인 책임 하에 개발 중인 표준 10개 목록▷ISO/CD 16293-2 Glass in building — Basic soda lime silicate glass products — Part 2: Float glass▷ISO/CD 18178 Glass in building — Laminated solar photovoltaic glass for use in buildings▷ISO/CD 19916-4 Glass in building — Vacuum insulating glass — Part 4: Pendulum impact testing and classification of safety glass▷ISO/DIS 20492-1 Glass in buildings - Insulating glass — Part 1: Durability of edge seals by climate tests▷ISO/DIS 20492-2 Glass in buildings - Insulating glass — Part 2: Chemical fogging tests▷ISO/DIS 20492-3 Glass in buildings — Insulating glass — Part 3: Gas concentration and gas leakage▷ISO/DIS 20492-4 Glass in buildings — Insulating glass — Part 4: Methods of test for the physical attributes of edge seals▷ISO/CD 28278-1 Glass in building — Glass products for structural sealant glazing — Part 1: Supported and unsupported monolithic and multiple glazing▷ISO/CD 28278-2 Glass in building — Glass products for structural sealant glazing — Part 2: Assembly rules▷IEC/AWI 63092-3 Photovoltaics in buildings — Part 3: Evaluation methodology of SHGC for Building integrated photovoltaic modules with various designs
-
[특집-기술위원회] TC 154 - 상업, 산업 및 행정 분야 프로세스, 데이터 요소 및 문서(Processes, data elements and documents in commerce, industry and administration)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다. 기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다. ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다. 1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다. 이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다. △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136, △1970년 TC 137, TC 138, TC 142, TC 145, △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 등도 포함된다. ISO/TC 154 상업, 산업 및 행정 분야 프로세스, 데이터 요소 및 문서(Processes, data elements and documents in commerce, industry and administration)와 관련된 기술위원회는 1972년 결성됐다. 사무국은 중국 국가표준화관리위원회(国家标准化管理委员会, Standardization Administration of the P. R. C, SAC))에서 맡고 있다. 위원회는 장 지안팡(Mr Jianfang Zhang)이 책임지고 있다. 현재 의장은 유 시(Mr Yu Shi)로 임기는 2024년까지다. ISO 기술 프로그램 관리자는 로라 매튜(Ms Laura Mathew), ISO 편집 관리자는 이본느 헨(Mrs Yvonne Chen) 등으로 조사됐다. 범위는 비즈니스, 행정 프로세스의 국제 표준화 및 등록이다. 또한 개별 조직 내 및 조직간 정보 교환에 사용되는 지원 데이터의 국제 표준화 및 등록, 산업 데이터 분야의 표준화 활동을 지원한다. 다음과 같은 애플리케이션별 메타 표준 개발 및 유지 관리도 포함된다. △프로세스 사양(다른 기술위원회의 개발이 없는 경우) △콘텐츠가 포함된 데이터 사양 △양식 레이아웃(종이/전자) △표준 개발 및 유지 관리 △프로세스 식별(다른 기술위원회의 개발이 없는 경우) △데이터 식별 △EDIFACT 구문의 유지 관리 현재 ISO/TC 154 사무국의 직접적인 책임 하에 발행된 표준은 37개며 SO/TC 154 사무국의 직접적인 책임 하에 개발 중인 표준은 7개다. 참여하고 있는 회원은 17개국, 참관 회원은 28개국이다. □ ISO/TC 154 사무국의 직접적인 책임 하에 발행된 표준 37개 중 15개 목록 ▷ISO 5054-1:2023 Specification for an enterprise canonical model — Part 1: Architecture ▷ISO 6422-1:2010 Layout key for trade documents — Part 1: Paper-based documents ▷ISO 7372:2005 Trade data interchange — Trade data elements directory ▷ISO 8439:1990 Forms design — Basic layout ▷ISO 8440:1986 Location of codes in trade documents ▷ISO 8440:1986/Cor 1:2000 Location of codes in trade documents — Technical Corrigendum 1 ▷ISO 8601-1:2019 Date and time — Representations for information interchange — Part 1: Basic rules ▷ISO 8601-1:2019/Amd 1:2022 Date and time — Representations for information interchange — Part 1: Basic rules — Amendment 1: Technical corrections ▷ISO 8601-2:2019 Date and time — Representations for information interchange — Part 2: Extensions ▷ISO 9735-1:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 1: Syntax rules common to all parts ▷ISO 9735-2:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 2: Syntax rules specific to batch EDI ▷ISO 9735-3:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 3: Syntax rules specific to interactive EDI ▷ISO 9735-4:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 4: Syntax and service report message for batch EDI (message type — CONTRL) ▷ISO 9735-5:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 5: Security rules for batch EDI (authenticity, integrity and non-repudiation of origin) ▷ISO 9735-6:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 6: Secure authentication and acknowledgement message (message type - AUTACK) □ ISO/TC 154 사무국의 직접적인 책임 하에 개발 중인 표준 7개 목록 ▷ISO/WD 5909 Data interchange processes of blockchain based negotiable maritime bill of lading related to e-Commerce platform ▷ISO/AWI 7372 Trade data interchange — Trade data elements directory ▷ISO 8601-2:2019/DAmd 1 Date and time — Representations for information interchange — Part 2: Extensions — Amendment 1 ▷ISO/AWI 14533-3 Processes, data elements and documents in commerce, industry and administration — Long term signature profiles — Part 3: Long term signature profiles for PDF Advanced Electronic Signatures (PAdES) ▷ISO/WD TR 19626-3 Processes, data elements and documents in commerce, industry and administration —Trusted communication platforms for electronic documents — Part 3: Blockchain-based implementation guideline ▷ISO/DIS 20197-1 Buy-Ship-Pay Reference Data Model — Part 1: Business Requirement Specification (BRS) ▷ISO/DIS 23355 Visibility data interchange between logistics information service providers
-
[특집-기술위원회] TC 132 - 합금철(Ferroalloys)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127 등도 포함된다.ISO/TC 132 합금철(Ferroalloys)과 관련된 기술위원회는 TC 130, TC 131과 마찬가지로 1969년 결성됐다. 사무국은 중국 국가표준화관리위원회(国家标准化管理委员会, Standardization Administration of China, SAC)에서 맡고 있다.위원회는 롱 쓰우(Ms Rong ZHU)가 책임지고 있다. 현재 의장은 춴성 루(Mr Chunsheng LU)로 임기는 2027년까지다.ISO 기술 프로그램 관리자는 스테판 소바쥬(M Stéphane Sauvage), ISO 편집 관리자는 앤 기앳(Ms Anne Guiet) 등으로 조사됐다.범위는 철과 강철 제조에 사용되는 합금철 및 기타 합금 첨가제, 합금철 원료에 사용되는 망간 광석 및 크롬 광석 분야의 표준화다. 단, ISO/TC 155에 따른 페로니켈 표준화는 제외한다.현재 ISO/TC 132 사무국의 직접적인 책임 하에 발행된 표준은 69개며 ISO/TC 132 사무국의 직접적인 책임 하에 개발 중인 표준은 2개다. 참여하고 있는 회원은 7개국, 참관 회원은 26개국이다.□ ISO/TC 132 사무국 분과위원회(Subcommittee)의 책임 하에 발행된 표준 15개 목록▷ISO 310:1992 Manganese ores and concentrates — Determination of hygroscopic moisture content in analytical samples — Gravimetric methodISO 312:1986 Manganese ores — Determination of active oxygen content, expressed as manganese dioxide — Titrimetric method▷ISO 315:1984 Manganese ores and concentrates — Determination of nickel content — Dimethylglyoxime spectrometric method and flame atomic absorption spectrometric method▷ISO 317:1984 Manganese ores and concentrates — Determination of arsenic content — Spectrometric method▷ISO 320:1981 Manganese ores — Determination of sulphur content — Barium sulphate gravimetric methods and sulphur dioxide titrimetric method after combustion▷ISO 548:1981 Manganese ores — Determination of barium oxide content — Barium sulphate gravimetric method▷ISO 549:1981 Manganese ores — Determination of combined water content — Gravimetric method▷ISO 619:1981 Manganese ores — Determination of chromium content — Diphenylcarbazide photometric method and silver persulphate titrimetric method▷ISO 3713:1987 Ferroalloys — Sampling and preparation of samples — General rules▷ISO 4139:1979 Ferrosilicon — Determination of aluminium content — Flame atomic absorption spectrometric method▷ISO 4140:1979 Ferrochromium and ferrosilicochromium — Determination of chromium content — Potentiometric method▷ISO 4158:1978 Ferrosilicon, ferrosilicomanganese and ferrosilicochromium — Determination of silicon content — Gravimetric method▷ISO 4159:1978 Ferromanganese and ferrosilicomanganese — Determination of manganese content — Potentiometric method▷ISO 4293:1982 Manganese ores and concentrates — Determination of phosphorus content — Extraction-molybdovanadate photometric method▷ISO 4295:1988 Manganese ores and concentrates — Determination of aluminium content — Photometric and gravimetric methods □ ISO/TC 132 사무국 분과위원회(Subcommittee)의 책임 하에 개발 중인 표준 목록▷ISO/WD 6331 Chromium ores and concentrates — Determination of chromium content — Titrimetric method▷ISO/WD 7692 Ferrotitanium — Determination of titanium content — Titrimetric method□ ISO/TC 132 사무국의 작업그룹(Working Group, WG) 현황▷ISO/TC 132/WG 3 Chromium ores and concentrates - Determination of chromium content - Titrimetric method Working group▷ISO/TC 132/WG 4 Ferrotitanium— Determination of titanium content— Titrimetric method Working group
-
[특집-공동기술위원회] ④JTC 1/SC 2 코드화된 문자 세트(Coded character sets)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(Working Group, WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등을 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.또한 국제전기기술위원회(International Electro-technical Commission, IEC)는 전기 및 전자 제품의 고품질 인프라와 국제 무역을 뒷받침하는 글로벌 비영리 회원 조직이다.기술 혁신, 저렴한 인프라 개발, 효율적이고 지속 가능한 에너지 접근, 스마트 도시화 및 교통 시스템, 기후 변화 완화를 촉진하고 사람과 환경의 안전을 향상시키는 역할을 수행하고 있다. 170개 이상의 국가를 통합하고 전 세계 2만명의 전문가에게 글로벌하고 중립적이며 독립적인 표준화 플랫폼을 제공하고 있다. 장치, 시스템, 설치, 서비스 및 인력이 필요에 따라 작동함을 구성원이 인증하는 4가지 적합성 평가 시스템을 관리한다.적합성 평가와 함께 정부가 국가 품질 인프라를 구축하고 모든 규모의 기업이 전 세계 대부분의 국가에서 일관되게 안전하고 신뢰할 수 있는 제품을 사고 팔 수 있도록 하는 기술 프레임워크를 제공하는 약 1만개의 IEC 국제표준을 발행하고 있다.이러한 ISO와 IEC가 공동으로 구성한 기술위원회 ISO/IEC JTC 1 정보 기술(Information technology)에 대해 살펴볼 예정이다. JTC 1은 1987년에 결성됐으며 사무국은 미국국립표준협회(American National Standards Institute, ANSI)에서 맡고 있다. 위원회는 리사 라지첼(Mrs Lisa Rajchel)가 책임지고 있다. 현재 의장은 필 웬블롬(Mr Phil Wennblom)으로 임기는 202년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), 스티븐 더트널(Mr Stephen Dutnall), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등으로 조사됐다. 범위는 정보기술 분야의 표준화다.현재 ISO/IEC JTC 1의 직접적인 책임 하에 발행된 표준은 517개며 직접적인 책임 하에 개발중인 표준은 23개다. 참여하고 있는 회원은 40개국, 참관 회원은 62개국이다.공동 기술위원회(Joint Technical Committee, JTC) 산하에서 활동하고 있는 분과위원회(Subcommittee, SC) 중 첫 번째 SC 1 활동에 이어 SC 2에 대해 살펴보면 다음과 같다.ISO/IEC JTC 1/SC 2 코드화된 문자 세트(Coded character sets)와 관련된 분과위원회는 1987년 결성됐다. 사무국은 일본산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 나가사와 아유코(Ms Ayuko Nagasawa)가 책임지고 있다. 현재 의장은 마사루 타케치(Mr Masaru Takechi)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 스테판 소바쥬(M Stéphane Sauvage), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등으로 조사됐다.범위는 문자열 순서, 관련 제어 기능, 정보 교환을 위한 코드화된 표현 및 코드 확장 기술을 포함해 그래픽 문자 집합 및 특성의 표준화다. 단, 오디오 및 사진 코딩은 제외된다.현재 ISO/IEC JTC 1/SC 2 사무국의 직접적인 책임하에 발행된 표준은 49개며 개발 중인 표준은 3개다. 참여하고 있는 회원은 24명, 참관 회원은 26명이다.□ ISO/IEC JTC 1/SC 2 사무국의 직접적인 책임하에 발행된 표준 및(또는) 프로젝트 49개 중 15개 목록▷ISO/IEC 646:1991 Information technology — ISO 7-bit coded character set for information interchange▷ISO 962:1974 Information processing — Implementation of the 7- bit coded character set and its 7- bit and 8-bit extensions on 9- track 12,7 mm (0.5 in) magnetic tape▷ISO 1113:1979 Information processing — Representation of the 7- bit coded character set on punched tape▷ISO 1154:1975 Information processing — Punched paper tape — Dimensions and location of feed holes and code holes▷ISO 1681:1973 Information processing — Unpunched paper cards — Specification▷ISO/IEC 2022:1994/Cor 1:1999 Information technology — Character code structure and extension techniques — Technical Corrigendum 1▷ISO/IEC 2022:1994 Information technology — Character code structure and extension techniques▷ISO 2033:1983 Information processing — Coding of machine readable characters (MICR and OCR)▷ISO 2047:1975 Information processing — Graphical representations for the control characters of the 7- bit coded character set▷ISO/IEC 2375:2003 Information technology — Procedure for registration of escape sequences and coded character sets▷ISO 3275:1974 Information processing — Implementation of the 7- bit coded character set and its 7- bit and 8- bit extensions on 3,81 mm magnetic cassette for data interchange▷ISO/IEC 4873:1991 Information technology — ISO 8-bit code for information interchange — Structure and rules for implementation▷ISO 5426-2:1996 Information and documentation — Extension of the Latin alphabet coded character set for bibliographic information interchange — Part 2: Latin characters used in minor European languages and obsolete typograph▷ISO 5426:1983 Extension of the Latin alphabet coded character set for bibliographic information interchange▷ISO 5427:1984 Extension of the Cyrillic alphabet coded character set for bibliographic information interchange□ ISO/IEC JTC 1/SC 2 사무국의 직접적인 책임하에 개발중인 표준 및(또는) 프로젝트 3개 목록▷ISO/IEC CD TR 2375 Information technology – Registered escape sequences and coded character sets▷ISO/IEC 10646:2020/CD Amd 2.3 Information technology — Universal coded character set (UCS) — Amendment 2: Todhri, Garay, Tulu-Tigalari, Sunuwar, Gurung Khema, Kirat Rai, and other characters▷ISO/IEC CD 14651 Information technology — International string ordering and comparison — Method for comparing character strings and description of the common template tailorable ordering
-
[특집-기술위원회] TC101 - 연속으로 운반하는 기계적 장치스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC1~TC67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC68 △1950년 TC74 △1951년 TC76 △1952년 TC77 △1953년 TC79, TC81 △1955년 TC82, TC83 △1956년 TC84, TC85 △1957년 TC86, TC87, TC89 △1958년 TC91, TC92 △1959년 TC94 △1960년 TC96, TC98 등이다.ISO/TC 101 연속으로 운반하는 기계적 장치(Continuous mechanical handling equipment)와 관련된 기술위원회는 1961년 결성됐다. 사무국은 독일표준화협회(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 디터 웅거(Mr Dieter Unger)가 책임지고 있다. 현재 의장은 파비안 슐체(Mr Fabian Schültje)으로 임기는 2026년까지다.ISO 기술 프로그램 관리자는 패트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 빈센조 바추키(M Vincenzo Bazzucchi) 등으로 조사됐다.범위는 용어, 일반 설계, 구성, 주요 치수, 안전 요구 사항, 테트스, 검사 방법 등을 포함한 느슨한 벌크 재료 또는 단위 하중에 대한 연속으로 운반하는 기계적 장치 분야의 표준화다.현재 ISO/TC 101 사무국의 직접적인 책임하에 발행된 표준은 33개다. 참여하고 있는 회원은 11명, 참관 회원은 22명이다.□ ISO/TC 101 사무국의 직접적인 책임하에 발행된 표준 33개 중 15개 목록▷ISO 1049:1975 Continuous mechanical handling equipment for loose bulk materials — Vibrating conveyors and feeders with rectangular or trapezoidal trough▷ISO 1050:1975 Continuous mechanical handling equipment for loose bulk materials — Screw conveyors▷ISO 1535:1975 Continuous mechanical handling equipment for loose bulk materials — Troughed belt conveyors (other than portable conveyors) — Belts▷ISO 1536:1975 Continuous mechanical handling equipment for loose bulk materials — Troughed belt conveyors (other than portable conveyors) — Belt pulleys▷ISO 1537:1975 Continuous mechanical handling equipment for loose bulk materials — Troughed belt conveyors (other than portable conveyors) — Idlers▷ISO 1807:1975 Continuous mechanical handling equipment for loose bulk materials — Oscillating conveyors and shaking or reciprocating feeders with rectangular or trapezoidal trough▷ISO 1815:1975 Continuous mechanical handling equipment for loose bulk materials — Vibrating feeders and conveyors with tubular trough▷ISO 1816:1975 Continuous mechanical handling equipment for loose bulk materials and unit loads — Belt conveyors — Basic characteristics of motorized driving pulleys▷ISO 1819:1977 Continuous mechanical handling equipment — Safety code — General rules▷ISO 2109:1975 Continuous mechanical handling equipment — Light duty belt conveyors for loose bulk materials▷ISO 2139:1975 Continuous mechanical handling equipment for loose bulk materials — Oscillating conveyors and shaking or reciprocating feeders with tubular trough▷ISO 2140:1975 Continuous mechanical handling equipment for loose bulk materials — Apron conveyors▷ISO 2148:1974 Continuous handling equipment — Nomenclature▷ISO 2326:1972 Continuous mechanical handling equipment for loose bulk materials — Aeroslides▷ISO 2327:1972 Pneumatic handling appliances for loose bulk materials — Piping